Foxcom Platino de banda Ancha PL7450T/PL7450R4 conexión RF, Muy Alto Rango de Potencia, 4dB Presupuesto Óptico de 8 km - 1310 nm o 15Km - 1550nm
Foxcom Platinum Wideband PL7450T/PL7450R4 RF Link, rango de potencia muy alto, presupuesto óptico de 4dB 8Km - 1310nm o 15Km - 1550nm
• Más de 8 km. distancia [15Km con el PL7450T1550]
• Potentes capacidades de administración a través de una pantalla LCD en el panel frontal y SNMP montado en rack
• Control del usuario y configuración del nivel de IMD requerido
Foxcom Platinum Wideband PL7450T/PL7450R4 RF Link, Very High Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm
 |
||
| Summary | ||
| Foxcom Platinum Wideband PL7450T/PL7450R4 RF Link, Very High Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm Foxcom’s Platinum Wideband products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 4 dB optical budget with thePL7450R4 receiver. Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz. Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7450T transmitter and PL7450R4 receiver are designed for subrack chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering. The PL7450T transmitter and PL7450R4 receiver are optimized for cellular application where wide RF input power range is needed and high RF output power. | ||
| Order Diagram - Options | ||
 |
||
Foxcom Platinum Wideband PL7450T / PL7450R4 RF Link, Very High Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm
| RF Specifications | Units | Typical | Minimum | Maximum |
| Frequency Range - Bandwidth | MHz | 10 - 3000 | 3000 | |
| Amplitude Response @ Unity Gain 10 - 3000 MHz any 36 MHz |
dB |
±2 ±0.25 |
±2.25 ±0.3 |
|
| Gain Stability | dB/24hr | ± 0.2 | ± 0.25 | |
| Gain Slope1 | dB | 0 | -1.5 | +1.5 |
| Gain Variation over temperature | dB | ± 1.5 | -2 | 2 |
| SFDR2 | dB/Hz2/3 | 110 | ||
| SFDR3 | dB/Hz2/3 | 95 | ||
| DR (Dynamic Range - single channel)4 | dB | 50 | ||
| CNR [1Hz]2 | dB | 139 | 135 | 140 |
| Noise Figure (NF)2 | dB | 39 | 39 | 44 |
| Noise Figure (NF)3 | dB | 18 | 20 | 15 |
| Output IP3 (OIP3)5 | dBm | 20 | ||
| Group Delay Variation- linear 10 to 60 MHz 60 - 3000 MHz |
ns | 13 1.5 |
-15 -11 |
|
| Input/Output Impedance | Ohm | 50 or 75 | ||
| 1 dB Compression Point | dBm | 2 | 3 | |
| Phase Noise6 | dBm | None | ||
| Third Order InterModulation [IMD]4 | dBc | -55 | -40 | |
| Input Signal Range - Total Power7 | dBm | -50 | 0 | |
| Maximum Input without Damage | dBm | +15 | ||
| RF Output Signal Range - Total Power 8 9 | dBm | -25 -25 |
+15 +15 |
|
| TX/RX Input/Output Return Loss 50 Ohm 75 Ohm 13 |
dB | -15 -13 |
-15 -11 |
|
| Test Port [front panel sample port]10 | dB | -20 | -22 | -18 |
| RF Connector Type Input/Output Test Port |
SMA, N BNC |
|||
| Optical Specifications | Typical | Minimum | Maximum | |
| Optical Wavelength | nm | 1310/1550/CWDM | ||
| Optical Power Output | mW / dBm | 2 / 3 | 1.7/2.5 | |
| Optical Budget / Distance 4 dB optical budget |
dBm/Km | 1310 nm | 1550 nm 8 |15 |
||
| RX Optical Input Power | dBm | -1 | -2 | 4 |
| Optical Connector Types | Type | FC/APC or SC/APC (E2000 option) |
- | |
| Optical Return Loss | dB | -60 | -55 | |
| Electrical Specifications | ||||
| Supply Voltage | Vdc | 12 | ||
| Supply Current [TX]11 | Amps | 0.5 | ||
| Supply Current (RX) | Amps | 0.45 | ||
| EMI Rating | EMI Rating: FCC Class B CE Mark |
|||
| Physical Specifications | ||||
| Operating Temperature Range | ºC | -10 | +55 | |
| Storage Temperature Range | ºC | -45 | +85 | |
| Relative Humidity | 95% non-condensing | |||
| Altitude | ft / Km | 10,000 [3.08 ] operating12 14,000 [12.2] non-operating |
||
| Dimensions [D×W×H] | ins/cm | 12×0.8×4 / 30.5×2×10.2 | ||
| Weight | lbs./Kg | 0.5 / 0.23 | ||
| MTBF | Hours | TX: 309, 481 RX: 359, 057 |
||
| MTTR | Hours | 0.083 | ||
| Shock & Vibration | Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration. |
|||