Bienvenido a IK Tech Corporation
Su única parada para todas sus necesidades de satélites

Foxcom de Platino en Banda L PL7230T [PL7230T1550 ]/PL7230R4 de enlace Ascendente de Alta Potencia de Entrada, 4 dB Presupuesto Óptico

Foxcom de Platino en Banda L PL7230T [PL7230T1550 ]/PL7230R4 de enlace Ascendente de Alta Potencia de Entrada, 4 dB Presupuesto Óptico

Foxcom Platinum L-Band PL7230T [PL7230T1550]/PL7230R4 UpLink Entrada de alta potencia, presupuesto óptico de 4 dB

IKtechcorp es el distribuidor de Foxcom Communications Fiber Optic Systems, un fabricante y proveedor líder de equipos satelitales comerciales. Foxcom ofrece una amplia gama de enlaces de fibra utilizados en las industrias VSAT, DTH, COTM, Teleport, Cable y Broadcast. Satélite, DTH, VSAT, óptica, fibra óptica, RF

• Banda L: 950 - 3000 MHz
• Más de 8 Km [15 Km con el PL7230T1550]
• Potentes capacidades de gestión a través de una pantalla LCD en el panel frontal y SNMP montado en bastidor
• Control de usuario y configuración del nivel de IMD requerido
• Control de potencia del LNB a través de LCD o SNMP: +13 o 18 VDC
Código: Foxcom_PL7230R4

Foxcom Platinum L-Band PL7230T [PL7230T1550 ]/PL7230R4 UpLink High Power Input, 4 dB Optical Budget

Foxcom L-Band PL7230T [PL7230T1550 ]/PL7230R4 UpLink High Power Input, 4 dB Optical Budget
 
Summary

Foxcom L-Band PL7230T [PL7230T1550 ]/PL7230R4 UpLink High Power Input, 4 dB Optical Budget

Foxcom’s Platinum L-band products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full  4dB optical budget with thePL7230R4 receiver .

Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability.

In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz. 

Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications.

The PL7230T transmitters and the PL7230R4 receiver is designed for chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.

 

     
Order Diagram - Options    
Foxcom Gold Series Order Diagram - Options

Foxcom Platinum L-Band PL7230T [PL7230T1550 ] / PL7230R4 UpLink High Power Input, 4 dB Optical Budget

 

RF Specifications Units Typical Minimum Maximum
         
Frequency Range - Bandwidth MHz 950 - 3000   -
Amplitude Response @ Unity Gain
950–3000 MHz
any 36 MHz

dB

±1.25
±0.2
 
±1.5
±0.25
Gain Stability dB/24hr ±0.2   ± 0.25
Gain slope1 dB   -1.0 +1
Gain Variation over temperature dB   -2 2
SFDR2 dB/Hz2/3 105    
SFDR3 dB/Hz2/3 104    
DR (Dynamic Range - single channel)4 dB     30
CNR [any 36 MHz]3 dB 53   53
Noise Figure (NF)2 dB 30 28 33
Noise Figure (NF)3 dB 10 9 12
Output IP3 (OIP3)5 dBm - 15 20
Group Delay Variation- linear @
950 to 1200 MHz
1200 to 3000 MHz
ns
3
1.5
   
Input/Output Impedance Ohm 50 or 75    
1 dB Compression Point dBm 2   3
Phase Noise6 dB None    
Third Order InterModulation [IMD]7 dBc   -55 -40
RF Input Signal Range - Total Power dBm   -30 -5
Maximum input without damage       +15
Output Signal Range - Total Power8 dBm   -30 -5
TX/RX Input/Output Return Loss
50 Ohm
75 Ohm9
dB
-15
-13
 
-15
-11
Test Port [front panel sample port]10 dB -20 -22 -18
RF Connector Type
Input / Output
Test port
 
align=center>F, SMA, BNC, N
F, BNC
         
         
Optical Specifications   Typical Minimum Maximum
         
Optical Wavelength nm 1310/1550/CWDM    
Optical Power Output mW/dBm 2 / 3 1.7/2.5  
Optical Budget / Distance
4 dB optical budget
Km 1310 nm | 1550 nm
8 | 15
   
RX Optical Input Power dBm
-1

-2
4
Optical Connector Types Type FC/APC or SC/APC
(E2000 option)
   
Optical Return Loss dB   -60 -55
         
         
Electrical Specifications        
         
Supply Voltage Vdc 12    
Supply Current 11
TX, No LNB
TX with LNB
Amps
0.45
0.75
   
EMI Rating   EMI Rating: FCC Part 15 Class B
CE Mark
 
     
     
Physical/Environmental Specifications      
         
Operating Temperature Range ºC   -10 +55
Storage Temperature Range ºC   -45 +85
Relative Humidity   95% non-condensing    
Altitude ft / km

10,000 [3.08 ] operating12
14,000 [12.2] non-operating

   
Dimensions [D×W×H] ins/cm 12×0.8×4 / 30.5×2×10.2    
Weight lbs./Kg 0.5 / 0.23    
MTBF Hours TX: 309,481
RX: 359,057
   
MTTR Hours 0.083    
Shock & vibration Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration
         
1.   Within flatness spec
2.   -5 dBm RF input, link gain = 0 dB, IMD=-40 dBc @ 0 dBm optical input - max. RF input
3.   -30 dBm RF input, link gain =25 dB, IMD=-40 dBc @ 0 dBm optical input - min. RF input  
4.   User adjustable
5.   -5 dBm RF in @ IMD=-40 dBc
6.   Direct modulation utilized
7.   Adjustable. Above -10 dBm input min. -50 dBc
8.   Alarm trip point: RED -2 dBm, AMBER -33 dBm
9.   -15 dB @ 950 to 3000 MHz, -11 dB @ 2500 to 3000 MHz
10.   -45 dBm minimum input
11.   Under 10º add 120 mA for Tx [laser heating]
12.   WIth standard adiabatic derating at 2ºC/1000ft. [0.3 Km.]