Foxcom GL952CU C-Bande Optique de liaison Montante [5,8─6,8 GHz], 3dB Budget Optique

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], budget optique 3dB

IKtechcorp est le distributeur pour Foxcom Communications Fiber Optic Systems, l'un des principaux fabricants et fournisseurs d'équipements satellitaires commerciaux. Foxcom propose une large gamme de liaisons fibre optique utilisées dans les secteurs VSAT, DTH, COTM, Teleport, Cable et Broadcast. Satellite, DTH, VSAT, optique, fibre optique, RF.

• Optimisé pour les applications satellites professionnelles
• Large plage dynamique
• Distance de transmission de 15 km
• Contrôle de gain de l'émetteur et du récepteur
• Port de test du panneau avant
• Fonctions de surveillance puissantes
• Compatible avec tous les produits Sat-Light de 1ère génération

Code produit: foxcom_GL952CU

Appelez pour les Prix

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget



Summary
Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget Foxcom's Sat-Light C-Band fiberoptic interfacility links transmit and receive uplink signals in the 5.8─6.8 GHz range between antennas and control rooms or NOCs. Foxcom's IFLs offer a high performance alternative to conventional coaxial-cabled systems, reducing the need for waveguide and minimizing signal attenuation. The Sat-Light IFLs function as a transparent link, transmitting all satellite modulation formats carrying an entire polarization on each link. System limitations in using coaxial cable are overcome by the simplicity and performance of fiberoptic connections to provide the highest levels in signal quality. Foxcom achieves this by using state of the art lasers to provide high efficiency, low noise analog links. A typical C-Band link consists of an optical transmitter that receives the RF signal, transmits it over a single mode fiber to an optical receiver and reconverts the optical signal to RF. Foxcom's advanced fiberoptic technology reduces the attenuation, slope, phase shift, and group delay maintaining extremely low levels over distances of up to 15 kilometers. The C-Band's link cost effective high performance lasers produce negligible chirp and optical distortion, which is critical for long distance links. The EAM monolithic design, versus connectorized component electro-optics, assures high performance along with excellent reliability. The links are provided with test ports, status and fault LEDs, and gain controls.

Technical Specifications Diagram
Inquire

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget

RF Specifications	Units	Typical	Minimum	Maximum

Frequency Range	GHz	5.8─6.8
Link Gain	dB	Adjustable	0	0
Amplitude Response @ Unity Gain 5.8─6.8 GHz any 48 MHz	dB	±0.75 ±0.25
Gain Stability @ Constant Temp	dB/24hr			±0.15
SFDR	dB/Hz2/3		100
CNR [36 MHz @ 2.5GHz]	dB		45
Noise Figure (NF)	dB		28
Output IP3 (OIP3)	dB		+20
Third Order InterModulation [IMD]1	dBc	Adjustable	-50
Group Delay Variation- linear 3.4─4.2GHz	ns	0.4
Input Signal Range - Total Power	dBm		-20	-5
RF Output Signal Range - Total Power	dBm		-20	-5
Maximum Input without Damage 60sec	dBm		+5
Input/Output Impedance	ohm	50
TX/RX Input/Output VSWR @ 50 Ohm	dB		1.5:1
RF Connector Type Input/Output Test Port		SMA SMA
Test Port [front panel sample port]	dB	-20	-19	-21


Optical Specifications	Unit	Typical	Minimum	Maximum

Optical Power Output	dBm		-3	0
Optical Budget / Distance 3 dB optical budget	dB/Km	15Km @ 1550nm
Optical Connector Types		FC/APC
Optical Wavelength	nm	1550/CWDM


Electrical Specification

Supply Voltage	Vdc	13	12.7	18
Supply Current [TX]	Amps	0.8
Supply Current (RX)	Amps	0.5


Physical Specifications

Operating Temperature Range			-10	+55
Dimensions [D×W×H]		RX: 5” x 5” x 1.5” TX: 5” x 5” x 3”

Foxcom GL952CU RF Link KU-Band Uplink Datasheet (495.7KB)