Foxcom Platinum L-диапазон PL7220T [PL7220T1550] / PL7220R4 RF DownLink Низкая Входная мощность, оптический бюджет 4 дБ

Foxcom Platinum L-Band PL7220T [PL7220T1550]/PL7220R4 Низкая входная мощность нисходящего канала RF, оптический бюджет 4 дБ

Модель: Foxcom _PL7220R4

Foxcom Platinum L-Band PL7220T [PL7220T1550]/PL7220R4 RF DownLink Low Input Power, 4dB Optical Budget



Summary
Foxcom L-Band PL7220T [PL7220T1550]/PL7220R4 RF Link Low input power, 4dB Optical Budget Foxcom’s Platinum L-band products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With low RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 4 dB optical budget with thePL7220R4 receiver. Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz. Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7220T transmitters and the PL7220R4 receiver are designed for chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.

Order Diagram - Options

Foxcom Platinum L-Band PL7220T [PL7220T1550] / PL7220R4 RF DownLink Low Input Power, 4dB Optical Budget

RF Specifications	Units	Typical	Minimum	Maximum

Frequency Range - Bandwidth	MHz	950 - 3000		3000
Amplitude Response @ Unity Gain 950-3000 any 36 MHz	dB	±1.5 ±0.2		±2 ±0.25
Gain Stability	dB/24hr	± 0.2		± 0.25
Gain slope1	dB	0	-1.5	+1.5
Gain Variation over temperature	dB	± 1.5	-2	2
SFDR2	dB/Hz2/3	99
SFDR3	dB/Hz2/3	91
DR (Dynamic Range - single channel)4	dB			30
CNR [any 36 MHz]2	dB	53	50	57
Noise Figure (NF)2	dB	20		23
Noise Figure (NF)3	dB	8		11
Output IP3 (OIP3)4	dBm	-5
Group Delay Variation - linear 950 -1200 MHz 1200 - 3000 MHz	ns	3 1.5
Input/Output Impedance	Ohm	50 or 75
1 dB Compression Point [input]	dBm	-16		-15
Phase noise6	dB	None
Third Order InterModulation [IMD]4	dBc		-55	-40
Input Signal Range - Total Power7	dBm		-55	-25
Maximum input without damage	dBm			+15
RF output Signal Range - Total Power -35 dBm input8 -55 dBm input9	dBm		-30 -35	-25 -25
TX/RX Input/Output return loss 50 Ohm 75 Ohm10	dB	-15 -13		-15 -11
Test port [front panel sample port]11	dB	-20	-22	-18
RF Connector Type Input/Output Test port		F, SMA, N F, BNC


Optical Specifications		Typical	Minimum	Maximum

Optical Wavelength	nm	1310/1550/CWDM
Optical Power Output	mW/dBm	2 / 3	1.7/2.5
Optical Budget / Distance 1310nm 1550nm	dBm/km	4dB / 8Km 4dB / 15Km
RX Optical Input Power	dBm	-1	-2	4
Optical Connector Types	Type	FC/APC or SC/APC (E2000 option)	-
Optical Return Loss	dB		-60	-55


Electrical Specifications

Supply Voltage	VDC	12
Supply Current [TX, no LNB]12	Amps	0.45
Supply Current [TX with LNB]12	Amps	0.75		0.9
Supply Current (RX)	Amps	0.45
EMI Rating		EMI Rating: FCC part 15 Class A, CE Mark


Physical Specifications

Operating Temperature Range	ºC		-10	+55
Storage Temperature Range	ºC		-45	+85
Relative Humidity		95% non-condensing
Altitude	ft / km	10,000 [3.08 ] operating13 40,000 [12.2] non-operating
Dimensions [D×W×H]	ins/cm	12×0.8×4 / 30.5×2×10.2
Weight	lbs./Kg	0.5 / 0.23
MTBF	hours	TX 309, 481 RX 359, 057
MTTR	hours	0.083
Shock & vibration		Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration

1. Within the flatness spec 2. -25 dBm RF input link gain =0 IMD=-40 dBc @ 3 dB opt. budget [0 dBm optical input - max .RF input] 3 -55 dBm RF input link gain = 30 IMD=-50 dBc @ 3 dB opt. budget [0 dBm optical input - min.RF input] 4. User adjustable 5.. -25 dBm RF input, IMD=-40 dBc 6. Direct modulation utilized 7. Alarm trip point: RED -22 dBm, AMBER -58 dBm 8. @ 0 dB optical loss 9. @ 4 dB optical loss 10. -15 dB @ 950 to 3000 MHz, -11 dB @ 2500 to 3000 MHz 11. -45 dBm minimum ooutput 12. under 10ºC add 120 mA [laser heating] 13. WIth standard adiabatic derating at 2ºC/1000ft. [0.3 Km.]

Foxcom L-Band PL7220T [PL7220T1550] / PL7220R4 RF DownLink Datasheet (106.57KB)