Сеть ETI Tracon GPT 230
The GPT 230 Dual Channel Heat–Trace Control is a dual–point microprocessor–based heat–trace control thermostat. It is ideal for applications which require two independent heater–control Channels with Ground–Fault Equipment Protection (GFEP). Ideal uses include freeze protection, hot water temperature maintenance, grease line trace, tank heating, and other temperature monitoring and control applications.
- Adjustable Temperature Setpoint and Alarms Sensor Inputs
- Precision Monitoring and Control
- Ground–Fault Equipment Protection
- Automatic GFEP Circuit Self–Test
| Environmental | |
|---|---|
| Area Of Use | Non-hazardous Locations |
| Operating Temperature Range | −40 °F to 122 °F (−40 °C to 50 °C) |
| Enclosure | |
|---|---|
| Dimensions | 9.0″ (W) 12 4/5″ x (H) x 5 9/10″ (D) 229 mm (W) x 325 mm (H) x 150 mm (D) |
| Protection | NEMA 4X, IP66 |
| Cover Attachment | Polycarbonate cover |
| Cable Entries |
Two liquid-tight cable glands installed for Two liquid-tight cable glands installed for sensor and alarm leads, cable diameter 0.08” to 0.24” (2 mm to 6 mm)
Two 1.046″ holes to accommodate ¾” conduit fittings for power wiring connections |
| Material | Polycarbonate |
| Weight | 5.8 lb. (2.63 kg) |
| Mounting | Wall mount with flanges |
| Wiring Terminal Ratings | |
|---|---|
| Power | Barrier Strip Terminals for Line, Neutral, and Ground; use 10 AWG wires rated for at least 194 °F (90 °C) |
| Sensors | Terminal Block, rising cage clamp, 12–28 AWG leads |
| Alarm Relay | Terminal Block, rising cage clamp, 12–28 AWG leads |
| User Interfaces | |
|---|---|
| Pushbuttons | UP, DOWN, ENTER, TEST / RESET BACK |
| DIP Switches | RTD wiring configuration Panel lockout |
| Parameter Settings For Each Zone | |
|---|---|
| Temperature Setpoint Heat ON | Adjustable −99.9 °F to 999 °F (−73.3 °C to 537.7 °C) |
| Temperature Setpoint Heat OFF | Adjustable −99.9 °F to 999 °F (−73.3 °C to 537.7 °C) |
| Low–Temperature Alarm Threshold | −99.9 °F to 999 °F (−73.3 °C to 537.7 °C) Default 35 °F (−1.7 °C) |
| Low–Temperature Alarm Delay | 0 s to 3000 s 0 s to 3000 s Default 300 s |
| High–Temperature Alarm Threshold | −99.9 °F to 999 °F (−73.3 °C to 537.7 °C) Default 140 °F (60 °C) |
| High–Temperature Alarm Delay | 0 s to 3000 s Default 300 s |
| Low–Current Alarm Threshold | 0.0 A to 10.0 A Default 0.1 A |
| Low–Current Alarm Delay | 0 s to 300 s Default 5 s |
| High–Current Alarm Threshold | 0.0 A to 55.0 A Default 30.0 A |
| High–Current Alarm Delay | 0 s to 600 s Default 300 s |
| Ground Fault Limit Current | 1.0 mA to 300.0 mA Default 30 mA |
| Self–Test Interval | 1 h to 250 h when enabled Default 24 h |
| Temperature Unit | °F or ° C Default °F |
| Indicators | |
|---|---|
| Status Indicator |
Power (Green) Heater (Yellow) Low Temperature (Blue) Summary Alarm (Red) |
| Display | 27″ OLED graphic 128×64 |
| Summary Alarm Relay Reporting |
Low temperature High temperature Low load current High load current High Stuck relay Sensor fault Internal |
| Temperature Accuracy | +/− 2 °F (1 °C) |
| Temperature Sensors | |
| Temperature Inputs | (Included) Two Thermistors: 100k ohms at 25 °C, range −40 °F to 230 °F (−40 °C to 110 °C), 20ft Lead (25076)RTD Sensor: Platinum, Alpha = 0.00385, ITS–90, 100 ohms at 0 °CInput supports 2–wire, 3–wire, or 4–wire connection |
| (GFEP) Ground–Fault Equipment Protection | |
| Range | Adjustable 1mA to 300 mA Default 30 mA +/- 2% |
| Automatic Self Test | Verifies GFEP functionality every 24 hr., when the load is turned on, and when there is a load |
| Supply Voltage | 100 – 277 V ac 50/60 Hz |
| Controller Power Consumption | 5 W maximum, 2 W idle |
| Load Rating | 30 A, 100 – 277 V ac resistive |
ORDERING INFORMATION
| Order Number | Description |
|---|---|
| 25171 | Tracon MODEL GPT 230 Dual-Point General Purpose Heat–Trace Control |
| 25076 | Temperature Sensor (included) |
| 25300 | GPT 230 Installation Sheet |
| 25167 | GPT 230 Installation and Operation Manual |