Foxcom Platinum L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget
![Foxcom Platinum L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget](https://www.iktechcorp.com/image/cache/catalog/product/foxcom_l-band_pl7230t_pl7230r10_rf_uplink_10db_optical_800-500x500.jpg "Foxcom Platinum L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget")
![IKtechcorp is Foxcom Communications Fiber Optic Systems 的分销商，是商业卫星设备的领先制造商和供应商。Foxcom 提供广泛的光纤链路，用于 VSAT、DTH、COTM、电信、电缆和广播行业。卫星、DTH、VSAT、光学、光纤、射频。”/></p> • L 波段：950 – 3000 MHz<br /> • 超过 25 公里。距离 [PL7230T1550 40 公里]<br /> • 通过前面板 LCD 和机架安装 SNMP 提供强大的管理能力<br /> • 用户控制和设置所需的 IMD 级别<br /> • 通过 LCD 或 SNMP 控制 LNB 功率： +13 或 18 VDC<br /></div>
<div class=](/image/catalog/media/foxcom_logo.jpg){kind=logo}
Foxcom Platinum L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget
![Foxcom L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget](/image/content/foxcom_l-band_PL7230T_PL7230R10_rf_uplink_10dB_optical_666.jpg) |
||
| Summary | ||
| Foxcom L-Band PL7230T [PL7230T1550]/PL7230R10 UpLink High Power Input 10 dB Optical Budget Foxcom’s Platinum L-band products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 10 dB optical budget with the PL7230R10 receiver. Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz. Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7230T[1550] transmitter and the PL7230R10 receiver are designed for chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering. | ||
| Order Diagram - Options | ||
 |
||
Foxcom Platinum L-Band PL7230T [PL7230T1550] / PL7230R10 UpLink High Power Input 10 dB Optical Budget
| RF Specifications | Units | Typical | Minimum | Maximum |
| Frequency Range - Bandwidth | MHz | 950 - 3000 | - | |
| Amplitude Response @ Unity Gain 950–3000 MHz any 36 MHz |
dB |
±1.25 ±0.2 |
±1.5 ±0.25 |
|
| Gain Stability | dB/24hr | ±0.2 | ± 0.25 | |
| Gain slope1 | dB | -1.0 | +1 | |
| Gain Variation over temperature | dB | -2 | 2 | |
| SFDR2 | dB/Hz2/3 | 105 | ||
| SFDR3 | dB/Hz2/3 | 104 | ||
| DR (Dynamic Range - single channel)4 | dB | 30 | ||
| CNR [any 36 MHz]3 | dB | 3 | 53 | |
| Noise Figure (NF)2 | dB | 30 | 28 | 33 |
| Noise Figure (NF)3 | dB | 10 | 18 | 23 |
| Output IP3 (OIP3)5 | dBm | - | 15 | 20 |
| Group Delay Variation linear @ 950 to 1200 MHz 1200 to 3000 MHz |
ns | 3 1.5 |
||
| Input/Output Impedance | Ohm | 50 or 75 | ||
| 1 dB Compression Point | dBm | 2 | 3 | |
| Phase Noise6 | dB | None | ||
| Third Order InterModulation [IMD]7 | dBc | -55 | -40 | |
| RF Input Signal Range - Total Power | dBm | -30 | -5 | |
| Maximum input without damage | +15 | |||
| Output Signal Range - Total Power8 | dBm | -30 | -5 | |
| TX/RX Input/Output Return Loss 50 Ohm 75 Ohm9 |
dB | -15 -13 |
-15 -11 |
|
| Test Port [front panel sample port]10 | dB | -20 | -22 | -18 |
| RF Connector Type Input / Output Test port |
F, SMA, N F, BNC =center> |
|||
| Optical Specifications | Units | Typical | Minimum | Maximum |
| Optical Wavelength | nm | 1310/1550/CWDM | ||
| Optical Power Output | mW/dBm | 2 / 3 | 1.7/2.5 | |
| Optical Budget / Distancet 10 dB optical budget |
Km | 1310 nm | 1550 nm 25 | 40 |
||
| RX Optical Input Power | dBm | -7 |
-8 |
4 |
| Optical Connector Types | Type | FC/APC or SC/APC (E2000 option) |
||
| Optical Return Loss | dB | -60 | -55 | |
| Electrical Specifications | ||||
| Supply Voltage | Vdc | 12 | ||
| Supply Current 11 TX, No LNB TX with LNB |
Amps | 0.45 0.75 |
||
| EMI Rating | EMI Rating: FCC Part 15 Class B CE Mark |
|||
| Physical/Environmental Specifications | ||||
| Operating Temperature Range | ºC | -10 | +55 | |
| Storage Temperature Range | ºC | -45 | +85 | |
| Relative Humidity | 95% non-condensing | |||
| Altitude | ft / km | 10,000 [3.08 ] operating12 |
||
| Dimensions [D×W×H] | ins/cm | 12×0.8×4 / 30.5×2×10.2 | ||
| Weight | lbs./Kg | 0.5 / 0.23 | ||
| MTBF | Hours | TX: 309,481 RX: 359,057 |
||
| MTTR | Hours | 0.083 | ||
| Shock & vibration | Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration | |||
| 1. Within flatness spec 2. -5 dBm RF input, link gain = 0 dB, IMD=-40 dBc @ 0 dBm optical input - max. RF input 3. -30 dBm RF input, link gain =25 dB, IMD=-40 dBc @ 0 dBm optical input - min. RF input 4. User adjustable 5. -5 dBm RF in @ IMD=-40 dBc 6. Direct modulation utilized 7. Adjustable. Above -10 dBm input min. -50 dBc 8. Alarm trip point: RED -2 dBm, AMBER -33 dBm 9. -15 dB @ 950 to 3000 MHz, -11 dB @ 2500 to 3000 MHz 10. -45 dBm minimum input 11. Under 10º add 120 mA for TX [laser heating] 12. WIth standard adiabatic derating at 2ºC/1000ft. [0.3 Km.] |
||||